Everything You Need To Know About How To Use a Table Saw

How To Operate a Table Saw

Set height of blade

Before you turn on the table saw, set the blade height about 1/8-in. above the top surface of the material being cut. There is much debate about how high a blade should run, but for safety purposes, keeping minimal blade exposure above the wood decreases the chances of injury or kickback.

Position the fence

Use a measuring tape to verify the desired measurement from the side of the blade facing the fence to the edge of the rip fence. Consider the kerf or thickness of your blade and adjust your measurement accordingly. Lock the rip fence into place. The position of the rip fence may adjust slightly when you lock it into place, so double-check your measurement with the fence locked and make any necessary adjustments before cutting.

Prep for the cut

Position the wood flush against the fence at the starting edge of the table without turning on the table saw. Plan how you will position your hands as you move the material forward. Ensure the blade guard is properly positioned. Make sure the push sticks are within reach for when you reach that part of the cut. If using a gripper or feather board, set up the position for smooth material flow. Plan your exit strategy by clearing the path where cut pieces will fall and consider outfeed support for longer pieces.

Turn on table saw and introduce wood

Turn on the table saw and allow the blade a few seconds to get up to running speed. Position the piece of wood firmly against the rip fence and slowly feed the wood into the blade. Ensure it enters straight and aligned. As you cut, keep your eye on the contact between the wood and the rip fence. As you push the wood forward into the blade, keep downward pressure to ensure the wood rides smoothly and evenly on the table surface. Maintain a steady, controlled feed rate – don’t rush the cut. Keep your hands clear of the blade path and never reach over the blade. Be prepared to switch to push sticks when your hands get close to the blade. If the wood binds or kicks back, immediately step aside and turn off the saw before addressing the issue.

Using a push stick

As you push the wood through the blade, keep your hands at least six inches away from the blade. If your wood board is wide enough to do it without a push stick, continue pushing until you’ve completed the cut. If not, use a push stick.

Position your push stick on the wood board before your hands get too close, placing them to maintain pressure against both the rip fence and table surface. Use the push sticks to keep wood in the proper position and push through to complete the cut, continuing to apply pressure against the fence and table until the cut wood is pushed beyond the spinning blade. Turn off the saw, and do not reach for either piece of cut wood until the table saw blade has completely stopped running.

Using a feather board

A feather board allows the user to keep fingers safely away from the blade when making delicate or thin cuts. It also keeps constant pressure against the rip fence for the whole length of the cut, making for more accurate measurements with your cuts. The feather board also helps prevent kickback.

Before positioning your wood, clamp the feather board to the table approximately one to two inches in front of the blade, ensuring it pushes the wood into the rip fence. Adjust the pressure so it’s firm enough to maintain contact but not so tight that it binds or holds back the wood as it moves forward. Feather boards work best on straight cuts with consistent material thickness. They should not be used on warped wood or very short pieces. Push through with a push stick and allow the feather board to guide the cut, maintaining consistent pressure against the fence throughout the entire cut.

FAQ

When making thin cuts on a table saw, should the thin piece ride along the rip fence or on the outside of the blade?

Whenever making thin rips on a table saw, always ride the wider piece of the wood along the rip fence and allow the thin piece to be the drop off. Use a feather board to maintain the wood position without having to place your hand or a push stick too close to the blade.

Which blade is best for my table saw?

Rule number one with any tool: match the blade to the material. If you are a basic DIYer or a woodworking weekend warrior, look for a general-purpose table saw blade. Carbide blades give you longer life when working with composite materials. High-speed steel usually provides cleaner cuts, which is important if you are doing cabinet-grade work and want to avoid tearout. Be sure to follow the manufacturer’s recommendations when it comes to selecting the right blade for your table saw and project at hand.

Can table saw blades be sharpened for re-use?

Yes. This is common practice, especially when purchasing more expensive blades. Look for a blade sharpening company in your area, give them a call and drop them off. Sharpened blades can be turned around in a few days, and the sharpening costs are usually less than half the price of the original purchase.

The post Everything You Need To Know About How To Use a Table Saw appeared first on Family Handyman.

For top-notch cleaning services, look no further than mj cleaning services, where quality and customer satisfaction are our top priorities. Whether you're in need of a one-time cleaning or ongoing maintenance, m j cleaning services offers a wide range of options to suit your requirements. With a reputation for excellence, m.j. cleaning services delivers professional and reliable cleaning solutions to ensure your home or office stays pristine and welcoming.